Fits Any Manufacturer
Replaces Rear Sight
Off Set Scope Mount
No Other Work Required
Does NOT Include Scope
Includes 1 Inch S&K Style Rings
Made In The USA
Didn’t think it was possible to easily put a scope and mount on your old M1 Garand without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!
S&K Scope Mounts LLC specializes in manufacturing scope mounts for ex-military rifles without the need for drilling & tapping. Now you can scope that rifle you didn't think was possible with over 100 Insta-Mounts & Scout Mounts to choose from. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.
For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required
S&K INSTA MOUNT BASES
The BEST WAY to mount a scope on your ex-military rifle. WHY?
-No major alteration to your valuable firearm
-No drilling or tapping of the ultra-hard receiver
-Guaranteed to hold zero
-Low cost for a quality product made in the USA!
-Can be removed and/or reinstalled easily
-Made In The USA
ADVANTAGES OF S&K MOUNTING SYSTEM
-Front and rear rings are interchangeable
-Ring studs mate to matching receptacles in bases
-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)
-Trim in appearance, light in weight
-Precision bored – scope will not slip
-No knobs, bolts or other obtrusions to break or bend
-Fits any 1 inch scope tube
All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.
INSTRUCTION SHEET TO INSTALL THE S&K INSTA-MOUNT ON YOUR M-1 GARAND #1865
Completely remove the rear sight and rear sight cover.
Using needle nosed pliers, place the rear sight provided into the center hole in the groove in the mount base. Screw it down so that the 1/8th hole in the sight is about 7/8th inch above bottom of base. Put one short 10-32 set screw in the cross hole and tighten JUST enough to keep the rear sight from turning accidentally, but no more. Please note this cross-hole is angled downward somewhat.
Install the insta -mount base. Carefully align the 3/8th hole in the rifle’s receiver and install shoulder screw. Tighten as tight as possible but do not use extension on key. Adjust the iron sight for elevation (windage is effected by moving front sight in opposite direction you want the bullet to go.) Remove the base, snug set screw against the rear sight and re-install mount base.
Place one 10-32 set screw in the rear most tapped hole in the milled groove in mount base, tighten as tight as possible. Place second 10-32 set screw in the front hole and tighten only as much as the short arm on the key will permit. Place scope in position with turret far enough forward to clear an ejected clip and collimate (some elevation can be effected by loosening and tightening of the two set screws alternately.)
Should the slot in the mount that slides over one of the seriated ears on the receiver be so tight that it can’t be tapped into place with a plastic hammer you can either file or mill the slot to fit the receiver. You can also return the mount to S&K (the maufacturer) for machining. We will need to know the slot width you desire. There is no charge for this service other than shipping.(Offered from the manufacturer)
NOW YOU ARE READY TO RANGE TEST YOUR RIFLE!
NOTE: SOME SCOPES WILL BE FOUND TO HAVE THEIR TURRETS IN A LOCATION THAT WILL NOT PERMIT A CLIP TO EJECT PROPERLY. IN A CASE SUCH AS THIS, IT MAY BE NECESSARY TO ROTATE THE SCOPE 90 DEGREES TO THE LEFT.
CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/