0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Mauser
  5. Scope Mounts
  6. S&K Carcano 91 Long Rifle w/ 600 - 2000 sight / Carcano 91/24 Carbine w/ 600 – 1500 sight (Weaver Style) -Accepts Weaver Rings- Rings NOT Included
S&K Carcano 91 Long Rifle w/ 600 - 2000 sight / Carcano 91/24 Carbine w/ 600 – 1500 sight (Weaver Style) -Accepts Weaver Rings- Rings NOT Included
S&K Carcano 91 Long Rifle w/ 600 - 2000 sight / Carcano 91/24 Carbine w/ 600 – 1500 sight (Weaver Style) -Accepts Weaver Rings- Rings NOT Included

S&K Carcano 91 Long Rifle w/ 600 - 2000 sight / Carcano 91/24 Carbine w/ 600 – 1500 sight (Weaver Style) -Accepts Weaver Rings- Rings NOT Included

1 Review(s) Write a Review
Price: $99.00
This solid S&K Carcano Mount will provide a base for your long eye relief scope. Made In The USA!!
Part Number: 9124
Availability:

Fits Carcano 91 Long Rifle w/ 600 - 2000 sight

Fits Carcano 91/24 Carbine w/ 600 – 1500 sight (Weaver Style)

Weaver Base

1.938" Hole Spacing - MEASURE BEFORE ORDERING

Scout Mount Replaces Rear Sight

Scope and Rings Not Included

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Carcano without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required


S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


#9124 Installation Instructions:
 Carcano 91 Long Rifle & 91/24 Carbine

You first have to remove the rear sight. This is done by removing the two screwdriver slotted screws from the right side of the rear sight. If you find they are extremely tight you might have to put some heat on the threaded part of the screws on the left side. After you get the screws out you need to pry the rear sight up as it lifts up off a lug that the screw you removed goes thru. If you find lifting the sight up is difficult you should remove wood from the receiver & barrel then you can pry the rear sight up much easier.

After you have the rear sight off, the pockets in the bottom of the S&K mount will fit down over the two mounting lugs on the rifle.  Install the two 6-32 x 7/8 socket head cap screws into the counter bored holes on the left side of the mount using a 7/64 hex wrench. Screw them in until they are just snug. Install the four 8-32 x 3/16th socket set screws into the two front & two rear holes PART WAY using a 5/64 hex wrench. Use caution not to cross thread these screws as the holes are on an angle. At the rear, screw one of the 8-32 screws in until it has some resistance & back it out 1 turn. Do the same with the opposite side. Now turn these two screws in equally until they are very lightly tightened. The front of the mount should move from side to side easily. If it doesn’t loosen one of the back two screws. At the front of the mount find what you believe to be the center of the side to side movement. With one hand hold the mount in place & snug the two front 8-32 screws until you feel a slight resistance. Use a collimator to sight the scope in or remove the bolt & bore sight. By loosening one of the two 8-32 front screws & tightening the other one you can get the scope centered. When centered tighten the four 8-32 screws holding onto the short end of the hex wrench so you can’t over tighten. Check to make sure you didn’t move off center. Now install the two 10-32 x 3/16 socket set screws using a 3/32 hex wrench & tighten by holding the short end of the hex wrench. Do your final windage & elevation adjustments with the turrets on the scope.


CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

Related Items

S&K #1 Mark III Lee Enfield Scout Mount Weaver Style (No Rings Included)
S&K #1 Mark III Lee Enfield Scout Mount Weaver Style (No Rings Included)
$80.00
Add To Cart
S&K Turkish Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
S&K Turkish Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
$91.00
Add To Cart
EGW Mauser 98 LR (3-Hole) Picatinny Rail Scope Mount 0 MOA (Military)
EGW Mauser 98 LR (3-Hole) Picatinny Rail Scope Mount 0 MOA (Military)
$39.00
Add To Cart
EGW Mini Mauser Zastava M85 Picatinny Rail Scope Mount 0 MOA Ambidextrous
EGW Mini Mauser Zastava M85 Picatinny Rail Scope Mount 0 MOA Ambidextrous
$39.00
Add To Cart
EGW HD Mosin Nagant 91/30 Picatinny Scope Mount 0 MOA - No Pin Hole
EGW HD Mosin Nagant 91/30 Picatinny Scope Mount 0 MOA - No Pin Hole
$89.00
Add To Cart
EGW Dumoulin Herstal Mauser SA Picatinny Rail 0 MOA
EGW Dumoulin Herstal Mauser SA Picatinny Rail 0 MOA
$39.00
Add To Cart

Browse Similar Items

Recently Viewed Items