0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Old Military Rifle Scope Mounts
  5. S&K Yugo 48, 24-47, 52C and 48A Scout Mount w/S&K Style 1 Inch Rings
S&K Yugo 48, 24-47, 52C and 48A Scout Mount w/S&K Style 1 Inch Rings
S&K Yugo 48, 24-47, 52C and 48A Scout Mount w/S&K Style 1 Inch Rings

S&K Yugo 48, 24-47, 52C and 48A Scout Mount w/S&K Style 1 Inch Rings

Write a Review
Price: $91.00
Yugo 48 scout mount will mount a long eye relief scope to the rear sight of your old military rifle. Made with pride in the USA.
Part Number: 9865

Fits the Yugo, 24-47, 52C and 48A

Scout Mount

Replaces Rear Sight

No alteration needed

Includes 1 Inch S&K Style Rings

All Mounts marked "S&K Style Rings" do NOT work with Weaver Rings

Scope Not Included

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Yugo, 24-47, 52C or 48A without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required



The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


-Front and rear rings are interchangeable

-Ring studs mate to matching receptacles in bases

-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)

-Trim in appearance, light in weight

-Precision bored – scope will not slip

-No knobs, bolts or other obtrusions to break or bend

-Fit any 1 inch scope tube

All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8" diameter stud that locks into a 3/8" hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1" diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.


Remove the rear sight by pushing the pin out and remove the spring. Slide the special nut into the grove at the rear of the sight. Place the mount into the rear sight with the bottom hole over the special nut and the (2) side holes to the front of the gun. Put the 10-32 x ¾ (for #9865) or 10-32 x 5/8 (for #9870) flathead screw through the mount and into the special nut. (Do not tighten at this time)  Line the 6-32 tapped holes (in side of the mount) up with the holes in the side of the receiver. It is very important that these holes line up to keep from damaging the threads when the screws are installed. Insert the (2) 6-32 x 5/16 socket head cap screws through the hole the pin was in and into the mount. Lightly tighten the (2) 6-32 screws. Tighten down the 10-32 x ¾ (for #9865) or 10-32 x 5/8 (for #9870) flathead screw and then the (2) 6-32 x 5/16 socket head cap screws. You don’t need to get the (2) 6-32 screws very tight! Insert the 10–32 x ½ set screws into the threaded holes at the top of the mount & run these screws in until it puts pressure against the receiver and then tighten. Re-tighten the 10-32 x ½ set screws. After tightening the 10-32 set screws – Do not try to tighten or loosen the 6-32 side screws as the top set screws hold pressure on the 6-32 screws.

CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

Recently Viewed Items