My Account  |  0 item(s)    View Cart
Brass Stacker Mosin Nagant M38 & M44 See Thru Scout Scope Mount 

Brass Stacker Mosin Nagant M38 & M44 See Thru Scout Scope Mount 

Price: $85.00
Out Of Stock
Part Number: MN384453SSM
Steel Picatinny Rail, Mounts Over Rear Sight Block

***PLEASE READ SPECIFICATIONS & FITMENT NOTES BEFORE PURCHASING***

There is no need for bent bolt handle with this Mount.

 

FEATURES: Allows for mounting of Scout Scope or other long eye relief optics to Mosin Nagant models M38 & M44's without the need to drill & tap receiver or make any permanent modifications to firearm. It is designed to fit over rear sight block in order to allow for continued use of the original fixed/iron sights up to 100 meters. The Mount is rigid steel construction with Black Oxide finish. 100% Lifetime Warranty!

SPECIFICATIONS: This Mount utilizes the barrel pin hole and the pivot pin hole in the rear sight block. The Mount will accommodate a front to back (horizontal, parallel to bore axis) pin center distance of 1.56" (39.6mm) to 1.79" (45.4mm) and allows for an up and down (vertical, perpendicular to bore axis) pin center distance of .18" (4.6mm) to .41" (10.3mm). The Mount is designed to fit over rear sight blocks that measure between .750" (19.05mm) and .787" (20.00mm) wide. The total weight including hardware is 5.4 oz. Please note that we have made every reasonable effort to ensure that our Mount will work with the vast majority of M38 & M44's. If for any reason our Mount does not work with your specific M38 or M44 it can be returned (undamaged) for a full refund.

UNIT:

Mount: CNC laser cut perimeter, die punched holes and mounting slots, form tapped threads and die press formed. 3/32" (13 ga.) thick HR, P&O type CS-B A569 carbon steel; 40000 psi yield strength. Black Oxide plated.

Picatinny Rail: CNC machined to MIL-STD-1913. 8" long. HR ATSM A36 low carbon steel; 36000 psi yield strength. Black Oxide plated.

Screws: #10-32 x ¼" flat head socket cap screws. Alloy steel; Rc 38-45 hardness.

HARDWARE:

Bolts: M3x.5 X 30mm socket head cap screw. Grade 12.9 medium carbon Q&T alloy steel; Rc 38-44 hardness; 160000 psi yield strength, 177000 psi tensile strength; 1.67 ft lbs tightening torque.

Nuts: M3x.5 Hex Nut. Grade 2 low carbon steel; Rc 32 hardness; 60000 psi tensile strength. Black Oxide plated.

Lock Washers: 3mm cut spring lock washer. Steel. Black Oxide plated.

Flat Washers: 3mm plain flat washer. Steel. Black Oxide plated

Made In The USA

TOOLS PROVIDED:

Wrench: 2.5mm short arm hex key. Steel.

Drill: 3.00x41x70mm HSS Jobber. *Note: Drill is provided as a means to clean out or straighten existing pin holes.*

Punch: 3/32? x 7/8" dowel pin. Hardened 4140 alloy steel; Rc 47. ¼? x 2? Aluminum handle. *Note: This punch is not designed to be used on difficult to remove pins such as those soldered in place.* Complete installation instructions are supplied.

SCOPE & RINGS ARE NOT PROVIDED!

READ BEFORE ORDERING

FITMENT NOTES:

This mount will NOT work for a 9130! See Model 9130-SSM for a 9130.

The pin hole in the rear sight block is often located inconsistently as a result of the original manufacturing process. The pin hole, relative to the pivot pin, is frequently not parallel and may be out of alignment or skewed. The Mount can only accommodate so much of this misalignment. You should measure the center distances from barrel pin to pivot pin on both sides and check those with the dimensions listed in the SPECIFICATIONS to ensure that the mount will fit properly. A 3mm drill is provided and can be used to clean out and straighten (to some degree) without enlarging the barrel pin hole once the pin is removed. The barrel pin hole and pivot pin hole in the rear sight block are generally .118? (3.0mm) in diameter and the supplied 3mm bolts have a nominal OD of .115? (2.92mm). This tight fit along with the use of an appropriate liquid thread locker for the screws and nuts, as well as proper tightening of the same should result in no movement of the Mount during normal firing recoil.

READ ABOVE BEFORE ORDERING

TOOLS REQUIRED:

Safety glasses, heavy gloves, solid work surface or vise, hammer, flat blade screw driver, 7/32? (5.5mm) socket driver or wrench, hand drill, and liquid thread locker. A MAPP (Methyl Acetylene Propadience Propane) gas torch and heavy duty punch may be required to remove existing pins from the rear sight block if they are soldered in place. You can usually find these items at your local hardware or plumbers supply. The application of heat, if done properly, will not cause damage. Keep in mind that you only need to reach the melting point of the solder and that this same temperature was achieved during original construction without adverse effects. Procedure provided in supplied instructions.

NOTE:

As with ANY scope on ANY mount, should it receive an impact (dropped, hit, etc.) it should not be trusted to be accurate. Thus the SEE-THRU feature of our Mount. You can always still use the original iron or open sights if you feel the Mount has been compromised. Design subject to change without prior notice.

Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY & ensure an UNLOADED condition before beginning installation.


Recently Viewed Items