0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Old Military Rifle Scope Mounts
  5. S&K 1891 Argentine Mauser Short Rifle And Carbine Scout Mount (Weaver Style) Short Ladder-Accepts Weaver Rings- Rings NOT Included
S&K 1891 Argentine Mauser Short Rifle And Carbine Scout Mount  (Weaver Style) Short Ladder-Accepts Weaver Rings- Rings NOT Included
S&K 1891 Argentine Mauser Short Rifle And Carbine Scout Mount (Weaver Style) Short Ladder-Accepts Weaver Rings- Rings NOT Included

S&K 1891 Argentine Mauser Short Rifle And Carbine Scout Mount (Weaver Style) Short Ladder-Accepts Weaver Rings- Rings NOT Included

Write a Review
Price: $80.00
This solid S&K 1891 Argentine Mauser Short Rifle And Carbine Scout Mount will provide a base for your long eye relief scope. Made In The USA!!
Part Number: ARG90
Availability:

Weaver Base

Scout Mount Replaces Rear Sight

Scope and Rings Not Included

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old 1891 Argentine Mauser Short Rifle And Carbine without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required


S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


INSTRUCTION SHEET FOR THE ARGENTINE 1891 #ARG90

Push the pin out at the rear of the rear flip sight. Don’t lose this pin as it will be used to install the S&K mount. Remove the flip up sight, then the spring by sliding it forward and lifting it out. The spring may require you to remove a screw that holds it in place. Slide the special flange nut into the undercut at the front of the sight where the spring was. Keep the smooth edges toward the front & rear. Place the mount over the special flange nut & align the hole in the side of the receiver where the pin was removed with the side hole in the mount. Install the pin you removed from the OEM ladder sight. Put the 10-32 x 3/8 flat head screw through the mount and into the nut & tighten loosely. Put the 10-32 x 5/16 set screw down through the tapped hole in the top of the mount and tighten against the receiver. Tighten the set screw only as tight as you can using the short end of the allen wrench. Tighten the 10-32 x 3/8 flathead screw. The purpose of the set screw is to keep pressure on the side pin so it can’t back out & take up any slop there may be between the pin & holes.


CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

Recently Viewed Items