Fits a 1903, NOT
a 1903 A3
1465 Has bridge in rear. Use of high rings- no grinding
Stock Wood Removal Necessary
S&K Style 1 Inch High Rings Included
With The Use Of High Rings, You Can Use An Objective Up To And Including 50mm.
Scope Not Included
Made In The USA!!!
All Mounts marked "S&K Style Rings" do NOT work with
Didn’t think it was possible to easily put a scope and mount
on your old 1903 Springfield without drilling and tapping? It is now with high
quality, made in the USA scope mounts from S&K. These mounts are made with
high quality materials and backed by S&K Scope Mounts. Outfit your old
military rifle with a scope mount and long eye relief scope for better
accuracy, longer ranges, more confidence, and more fun hunting or on the range!
S&K Scope Mounts LLC specializes in manufacturing scope
mounts for ex-military rifles without the need for drilling & tapping. Now
you can scope that rifle you didn't think was possible with over 100
Insta-Mounts & Scout Mounts to choose from. S&K Scope Mounts LLC
supports American made. S&K manufactures all of their scope mounts here in
PA with the best USA materials available.
INSTRUCTIONS FOR INSTALLATION OF 1903 SPRINGFIELD #1465
The simple attractive and efficient design of this mount base makes it ideal for the shooter whom desires a fine mount but has little means with which to alter his firearm to accept a scope. To attach this base, proceed as follows:
1. Disassemble the firearm, removing the barrel and action from the stock.
2. Remove the bolt from the gun.
3. Take the receiver ring band we provided & spread it apart enough to slip over the barrel behind the rear sight. Squeeze it back together & install the 6-40 fillister head screw & tighten. (the screw with the screwdriver slot). This ring band is not
designed to fit the front of the receiver tight as it is used on several rifles.
4. Hold the INSTA-MOUNT base in your left hand with the bottom facing up, the slotted end facing away from you & the breach cutout toward the right. The forked nut fits into the 3/8” counter bored hole near the slotted end of the mount. The slanted end of the forked nut faces away from you toward the slotted end of the mount. Install with a 10-32 x 5/8 flat head screw. Do no tighten yet. Keep just loose enough that it will rotate.
5. Place the INSTA-MOUNT base so that its front is raised about 30 degrees over the receiver and place it on your gun so that the forked nut on the bottom slides into the clip slot at the rear of the bridge. Now pivot the front of the base downward to allow the base to come into full contact with the receiver. Install the 10-32 x 5/8 flat head screw through the top of the mount & into the ring band. Do not tighten – leave quite loose. Place the special end clamp plate into the slotted end at the rear of the mount with the countersunk hole facing outward. Install the 10-32 x 5/8 flat head screw. Do not tighten yet.
6. Tighten the screws in this order. The flat head screw on top of the base at the rear inserted into the forked nut. Push the mount toward the rear & tighten. The flat head screw in the end clamp plate at the rear of the base. Push the mount down & toward the rear & tighten. Before you proceed with tightening the last screw. Look at the forked nut from the under side of the receiver to make sure the angled sides of the forked nut are tight up against the receiver. If the tapered sides of the fork nut are tight against the receiver you won’t be able to squeeze the side of the mount & lift. If you can’t get this tight you can try two things.
1. Rotate the ring band 180 degrees – occasionally the threaded hole isn’t positioned correctly in the ring band & the ring band is keeping the mount from moving to the rear.
2. Chamfer the inside edge of the ring band hole & position the ring band with the chamfer toward the rear of the receiver. Now tighten the 10-32 x 5/8 flat head screw in the front of the base that threads into the ring band.
7. Some inletting of the wood will be necessary under the INSTA-MOUNT ring band area of your stock. A Dremmel tool works best to cut out the wood.
8. If you desire to use a scope with a large objective lens, it will be necessary to raise the scope or grind the bolt. We can supply ring risers at a reasonable cost if needed. The mount is supplied with high rings to allow a scope with a small rear bell to be used. Normally the high rings work with most scopes.
9. Install your scope on the gun before you replace the bolt to make sure the bolt will clear the rear bell of the scope when the bolt is placed into the receiver. If you choose to grind your bolt handle, be sure to allow enough clearance that the BOLT WILL NOT TOUCH THE SCOPE UNDER ANY CONDITION. If you find it necessary to replace your bolt with an altered one, be sure to have a competent gunsmith check the head-space.
Because some of these fine rifles show wear from re-finishing and other reasons, the clamping plate at the rear of the base has been re-designed to provide a “hook effect” when tightened. It may be necessary to grind or file a small amount off the bottom of this (make sure no more than necessary is removed) to clear the safety lug of the bolt. The purpose of the rear clamp is to hold rearward pressure on the mount & is not intended for holding the rear of the mount down. With rearward pressure the angle on the forked nut mates with the matching angle on the receiver & this is what holds it to the receiver down.