0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Old Military Rifle Scope Mounts
  5. S&K 1903 Springfield Scout Mount (Weaver Style)
S&K 1903 Springfield Scout Mount (Weaver Style)
S&K 1903 Springfield Scout Mount (Weaver Style)

S&K 1903 Springfield Scout Mount (Weaver Style)

2 Review(s) Write a Review
Price: $80.00
S&K 1903 Springfield Scout Mount (Weaver Style) accepts Weaver rings (not included) and allows you to add a long eye relief scope to your 1903 without permanent alterations to your vintage rifle.
Part Number: 0370
Availability:

Fits a 1903, NOT a 1903 A3

No Alteration Needed

Rings Not Included

Scope Not Included

Weaver Style Base / Accepts Weaver Rings (Not Included)

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old 1903 Springfield without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.



Instruction sheet for the 1903 Springfield Scout #0370

Push the pin out at the rear of the flip up sight. Remove the spring by lifting up at the front and sliding it forward. Slide the flange nut into the under cut at the front of the sight where the spring was. Place the mount over the flange nut with the (2) 4-40 tapped holes toward the but end. Line the 4-40 tapped holes in the mount up with the holes in the side of the receiver. It is very important that these holes line up to keep from damaging the threads when the screws are installed. Put in the (2) 4-40 socket head screws. DO NOT TIGHTEN!! Place a pin drill etc. through the countersunk hole in the top of the mount and into the hole in the special nut. Move the nut around with the pin until the round part of the nut slips into the counter bore in the bottom of the mount. Put the 10 – 32 x ¾ flat head screw through the mount and into the nut. Tighten this screw and then the (2) 4-40 screws. You don’t need to get the (2) 4-40 screws very tight! Put the 10-32 x ½ set screws down through the tapped hole in the top of the mount and tighten against receiver.
DO NOT try to remove the (2) 4-40 screws without first loosening the 10-32 front set screw

Related Items

S&K 1903 Springfield Scope Mount w/S&K Style 1 Inch Rings
S&K 1903 Springfield Scope Mount w/S&K Style 1 Inch Rings
$112.00
Add To Cart
S&K MAS 49/56- French Scope Mount (Weaver Style) -Accepts Weaver Rings- Rings NOT Included
S&K MAS 49/56- French Scope Mount (Weaver Style) -Accepts Weaver Rings- Rings NOT Included
$110.00
S&K Steyr M95 Infantry Scout Mount (Long Ladder Weaver Style) -Accepts Weaver Rings- Rings NOT Included
S&K Steyr M95 Infantry Scout Mount (Long Ladder Weaver Style) -Accepts Weaver Rings- Rings NOT Included
$80.00
Add To Cart
S&K Husqvarna Mauser 38 Scout Mount (S&K Style)  w/S&K Style 1 Inch Rings
S&K Husqvarna Mauser 38 Scout Mount (S&K Style)  w/S&K Style 1 Inch Rings
$91.00
Add To Cart
S&K Czechoslovakian 98/22 Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
S&K Czechoslovakian 98/22 Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
$91.00
Add To Cart
EGW Swedish Mauser 3 Hole for Stripper Clip 20 MOA Undrilled Picatinny Scope Mount Ambidextrous
EGW Swedish Mauser 3 Hole for Stripper Clip 20 MOA Undrilled Picatinny Scope Mount Ambidextrous
$39.00
Add To Cart

Browse Similar Items

Recently Viewed Items