Includes 1 Inch S&K Style Rings
Stripper Clips Cannot Be Used With Mount And Scope
Scope Mounts for classic military rifles by S&K
Manufacturing allows you to keep your rifle in collector condition without
drilling holes or altering the weapon, easy to install scope mount made of
quality materials, made in the USA. FN-49 Scope Mount
Scope Not Included
Made In The USA!!!
All Mounts marked "S&K Style Rings" do NOT
work with Weaver Rings
Didn’t think it was possible to easily put a scope and mount on your old FN-49 without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!
S&K Scope Mounts LLC specializes in manufacturing scope mounts for ex-military rifles without the need for drilling & tapping. Now you can scope that rifle you didn't think was possible with over 100 Insta-Mounts & Scout Mounts to choose from. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.
For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required
S&K INSTA MOUNT BASES
The BEST WAY to mount a scope on your ex-military rifle. WHY?
-No major alteration to your valuable firearm
-No drilling or tapping of the ultra-hard receiver
-Handsome ruggedness
-Guaranteed to hold zero
-Low cost for a quality product made in the USA!
-Unmatched versatility
-Can be removed and/or reinstalled easily
-Fast service
-Made In The USA
ADVANTAGES OF S&K MOUNTING SYSTEM
-Front and rear rings are interchangeable
-Ring studs mate to matching receptacles in bases
-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)
-Trim in appearance, light in weight
-Precision bored – scope will not slip
-No knobs, bolts or other obtrusions to break or bend
-Fits any 1 inch scope tube
All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.
#2065 INSTA MOUNT FOR THE 1949 FN – AUTO
To install your new insta-mount on the 1949 FN, simply remove the housing over the bolt at the rear of the receiver on your firearm. The S&K Insta-mount then slides into its place. Bolt the rear plate in place with the (2) 8-32 x 1/2 screws, making sure the spring is properly placed. Now lock the mount base in place by putting the (4) 10-32 x 1/4 pointed set screws into the holes in the top of the mount (single holes) and tightening. DO NOT over tighten. The side wall of the mount by the screw will bulge out if you are too tight. Move the bolt in & out. If the bolt seems like it slides hard, then loosen one of the top front pointed set screws. If the bolt is still tight then retighten the pointed set screw & loosen the one on the opposite side. Repeat this process until you find the pointed set screw/screws causing the problem. Almost always the problem is with one of the two front screws. When you find the screw that is causing the bolt to stick, replace the pointed set screw with one of the (2) 10-32 x 5/16 cup point set screws provided. CAUTION: you can replace only one pointed set screw in the front & if necessary one in the rear because your mount is held from shifting sideways with the pointed screws. What has caused this problem is the mount needs some clearance sideways & the set screws sometimes aren’t centered over the flat area on the receiver. Before inserting the pointed set screws into the mount look down into the holes & center the mount holes over the flat area of the receiver as best as you can. This sometimes helps.
Mount the steel ring risers into the two slots on top of the mount with the10-32 x ½ flat head screws, then put the scope rings in place on top. Follow accepted practice in sighting in and the job is done.
CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/
