0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Enfield
  5. S&K 4&5 Lee Enfield Scope Mount w/S&K Style 1 Inch Rings
S&K 4&5 Lee Enfield Scope Mount w/S&K Style 1 Inch Rings
S&K 4&5 Lee Enfield Scope Mount w/S&K Style 1 Inch Rings

S&K 4&5 Lee Enfield Scope Mount w/S&K Style 1 Inch Rings

Write a Review
Price: $99.00
Add a receiver scope mount to you Enfield with this Made In The USA mount!! Bring your vintage rifle into the present with a scope and improve your accuracy.
Part Number: 1165
Availability:

#4 Mark 1 or 2  #5 British Enfield Eddystone (Rear Sight),  Jungle Carbine (Rear Sight)

Fits any manufacturer

Replaces rear sight

No Other Work Required

Does NOT Include Scope

#1165 Includes 1 Inch S&K Style Rings

All Mounts marked "S&K Style Rings" do NOT work with Weaver Rings

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Lee Enfield or Jungle Carbine without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

S&K Scope Mounts LLC specializes in manufacturing scope mounts for ex-military rifles without the need for drilling & tapping. Now you can scope that rifle you didn't think was possible with over 100 Insta-Mounts & Scout Mounts to choose from. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.


For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required


S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


ADVANTAGES OF S&K MOUNTING SYSTEM

-Front and rear rings are interchangeable

-Ring studs mate to matching receptacles in bases

-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)

-Trim in appearance, light in weight

-Precision bored – scope will not slip

-No knobs, bolts or other obtrusions to break or bend

-Fits any 1 inch scope tube

All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases. 


INSTRUCTION SHEET FOR THE 4 & 5 LEE ENFIELD #1165

Remove the bolt, the rear sight and the spring loaded plunger found under the rear sight from rifle.

Place the base in location on the receiver of the gun with the (2) side holes to the rear. Line the 6-48 tapped holes in the mount up with the holes in the side of the receiver.  It is very important that these holes line up to keep from damaging the threads when the screws are installed. Pivot the mount downward to rest on the bridge while slipping the special wedge shaped nut, angle toward rear of receiver into its place. Thread the ¼-20 screw into the special nut but do not tighten. Do this carefully. When you have everything in place, tighten the two 6-48 screws in the rear & then tighten the ¼-20 socket head cap screw. If everything is seated correctly the bolt can be removed. Should the bolt catch on the special nut, try drilling the hole in the nut 1/64 larger. If this doesn’t work file or mill .005/.010 off the tapered part of the nut or return to S&K to have the .005/.010 removed.


CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/


Recently Viewed Items