Scout Mount
Replaces Rear Sight
Includes 1 Inch S&K Style Rings
All Mounts marked "S&K Style Rings" do NOT
work with Weaver Rings
Scope Not Included
Made In The USA!!!
Didn’t think it was possible to easily put a scope and mount on your old Budapest M95 Mauser without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!
Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.
For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required
S&K INSTA MOUNT BASES
The BEST WAY to mount a scope on your ex-military rifle. WHY?
-No major alteration to your valuable firearm
-No drilling or tapping of the ultra-hard receiver
-Handsome ruggedness
-Guaranteed to hold zero
-Low cost for a quality product made in the USA!
-Unmatched versatility
-Can be removed and/or reinstalled easily
-Fast service
-Made In The USA
ADVANTAGES OF S&K MOUNTING SYSTEM
-Front and rear rings are interchangeable
-Ring studs mate to matching receptacles in bases
-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)
-Trim in appearance, light in weight
-Precision bored – scope will not slip
-No knobs, bolts or other obtrusions to break or bend
-Fits any 1 inch scope tube
All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.
INSTRUCTION SHEET FOR BUDAPEST MAUSER M95 SCOUT MOUNT # 9565 and # 9570
Remove the rear sight by pushing the pin out. Push down on the flip-up sight & slide rearward. Remove the spring. Slide the special nut into the grove at the rear of the sight. Place the mount into the rear sight with the bottom hole over the special nut and the (2) side holes to the front of the gun. Put the 10-32 x ¾ (for #9565) or 10-32 x 5/8 (for #9570) flathead screw through the mount and into the special nut. (Do not tighten at this time) Line the 6-32 tapped holes (in side of the mount) up with the holes in the side of the receiver. It is very important that these holes line up to keep from damaging the threads when the screws are installed. Insert the (2) 6-32 x 5/16 socket head cap screws through the hole the pin was in and into the mount. Lightly tighten the (2) 6-32 screws. Tighten down the 10-32 x ¾ (for #9565) or 10-32 x 5/8 (for #9570) flathead screw and then the (2) 6-32 x 5/16 socket head cap screws. You don’t need to get the (2) 6-32 screws very tight! Insert the 10–32 x ½ set screw into the front top hole & snug down. Insert the 10–32 x 3/8 set screw into the rear top hold & snug down. Re-tighten the 10-32 x ½ set screws. After you have tightening the 10-32 set screws – Do not try to tighten or loosen the 6-32 side screws as the top set screws hold pressure on the 6-32 screws. Mount the scope & determine how much the rear of the scope needs raised. Remove the scope, loosen the 10-32 flat head screw & tighten the rear 10-32 set screw to raise the rear of the scope to the correct height. Retighten the 10-32 flat head screw. Repeat this procedure until the scope is sighted in.
CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/ 