S&K Carl Gustafs Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

Write a Review

Price: $92.00

This Carl Gustafs scout mount will mount a long eye relief scope to the rear sight of your old military rifle. Made with pride in the USA.

Part Number: CG65

Availability:

Quantity

Description

Will NOT Fit 94

Scout Mount

Replaces Rear Sight

Includes S&K Style 1 Inch Rings

Scope Not Included

No alteration needed

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Carl Gustafs without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required

S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA

ADVANTAGES OF S&K MOUNTING SYSTEM

-Front and rear rings are interchangeable

-Ring studs mate to matching receptacles in bases

-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)

-Trim in appearance, light in weight

-Precision bored – scope will not slip

-No knobs, bolts or other obtrusions to break or bend

-Fits any 1 inch scope tube

All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.

INSTRUCTIONS SHEET FOR CARL GUSTOF #CG65

Remove the rear sight ladder by pushing the hinge pin out with a 1/16” punch. Remove the leaf spring by sliding it forward (a strike with a punch & hammer might be required to dislodge it). Slide the special nut (with the short part of the head toward the rear) into the spring slot & all the way toward the rear of the slot. Set the S&K mount over the rear sight so the screw holes in the front of the S&K mount line up with the horizontal hinge pin holes in the rifle. Align the rear hole in the top of the S&K mount up with the special nut. It is very important that these holes all line up to keep from damaging the threads when the screws are installed. Put the two 4-40 x 5/16th socket head screws through the hinge pin holes in the receiver & into the tapped side holes in the mount. Do not tighten at this time. Put the 10-32 x ¾” flat head screw through the hole in the top of the mount & into the special nut but do not tighten. Now tighten the 4-40 socket head screws - You don’t need to get the (2) 4-40 screws very tight! Now tighten the 10-32 flat head screw. Screw the 10-32 x ½” socket set screw into the top of the mount in the front hole and tighten. This will hold upward pressure on the mount, eliminating any movement in the mount & locking the 4-40 screws in place. Do not try to tighten or loosen the 4-40 screws with the 10-32 set screw tight as you will damage or break the 4-40 screws.

CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

S&K Carl Gustaf M94 Mauser Scout Mount -Accepts Weaver Rings - Rings NOT Included

$82.00

Add To Cart

Carlson's Rifle And Pistol Snap Caps

$12.00

Select Options

Grovtec Non Detachable Locking Swivel Sets

$8.00

Select Options

S&K Carl Gustafs Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

Related Items

Browse Similar Items

Recently Viewed Items