0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Old Military Rifle Scope Mounts
  5. S&K Finnish M39 Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
S&K Finnish M39 Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
S&K Finnish M39 Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

S&K Finnish M39 Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

1 Review(s) Write a Review
Price: $91.00
Finnish M39 Mauser scout mount will mount a long eye relief scope to the rear sight of your old military rifle. Made with pride in the USA.
Part Number: FIN65
Availability:

Scout Mount

Replaces Rear Sight

Includes S&K Style 1 Inch Rings

No alteration needed

Scope Not Included

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Finnish M39 Scout without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!
Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required


S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


ADVANTAGES OF S&K MOUNTING SYSTEM

-Front and rear rings are interchangeable

-Ring studs mate to matching receptacles in bases

-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)

-Trim in appearance, light in weight

-Precision bored – scope will not slip

-No knobs, bolts or other obtrusions to break or bend

-Fits any 1 inch scope tube

All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases. 



#FIN65 Instruction sheet for the Finnish M 39 Scout
Remove the rear sight by pushing the hinge pin out and remove the sight and spring. Center the mount over the rear sight area and push the mount down between the standing ears. Install the two 4-40 x 5/16 socket head cap screws in each side at the front of the mount. Put the 4 x 12 mm socket head cap screw through the top of the mount and into the receiver. The 10 -32 x ½ set screw goes through the top of the mount and is tightened against the receiver. Re tighten all screws.



CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

Recently Viewed Items