0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. M14 / M1A
  5. Scope Mounts
  6. S&K M1A and M14 Scope Mount w/S&K Style 1 Inch Rings
S&K M1A and M14 Scope Mount w/S&K Style 1 Inch Rings
S&K M1A and M14 Scope Mount w/S&K Style 1 Inch Rings

S&K M1A and M14 Scope Mount w/S&K Style 1 Inch Rings

Write a Review
Price: $111.00
This M1A / M14 mount is a rock solid scope mount for your M14 or M1A rifle. Bring your vintage rifle into the present with optics for better accuracy. Made In The USA.
Part Number: 1765

Fits any manufacturer

Fits Left Side

Allows Use of Iron Sights

No Other Work Required

Does NOT Include Scope

Includes 1 Inch S&K Style Rings

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old M14 or M1A without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

S&K Scope Mounts LLC specializes in manufacturing scope mounts for ex-military rifles without the need for drilling & tapping. Now you can scope that rifle you didn't think was possible with over 100 Insta-Mounts & Scout Mounts to choose from. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required


The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


-Front and rear rings are interchangeable

-Ring studs mate to matching receptacles in bases

-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)

-Trim in appearance, light in weight

-Precision bored – scope will not slip

-No knobs, bolts or other obtrusions to break or bend

-Fits any 1 inch scope tube

All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8 Inch diameter stud that locks into a 3/8 Inch hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1 Inch diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases. 

Instruction sheet for M1A or M-14 #1765

To install your mount, place the side plate on the left of the receiver, with mounting rails engaged into the grooves cut into the receiver. Install the washer, then install the screw and lock the side plate into place by tightening the screw securely. (We changed from the previous thumb screw to the heavy washer and 12-32 x 5/8th SHCS) Put the top-plate in place, and tighten the socket head cap screws. Install the scope rings according to instructions found on box.

CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

Recently Viewed Items