Scout Mount
Fits Mosin Nagant 91/30 & 91/59
Replaces Rear Sight
No alteration needed
Includes S&K Style 1 Inch Rings
Scope Not Included
For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required
S&K INSTA MOUNT BASES
The BEST WAY to mount a scope on your ex-military rifle. WHY?
-No major alteration to your valuable firearm
-No drilling or tapping of the ultra-hard receiver
-Handsome ruggedness
-Guaranteed to hold zero
-Low cost for a quality product made in the USA!
-Unmatched versatility
-Can be removed and/or reinstalled easily
-Fast service
-Made In The USA
ADVANTAGES OF S&K MOUNTING SYSTEM
-Front and rear rings are interchangeable
-Ring studs mate to matching receptacles in bases
-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)
-Trim in appearance, light in weight
-Precision bored – scope will not slip
-No knobs, bolts or other obtrusions to break or bend
-Fit any 1 inch scope tube
All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8" diameter stud that locks into a 3/8" hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1" diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.
#9165 INSTRUCTION SHEET FOR THE MOSIN NAGANT 91/30 & 91/59
PUSH THE PIN OUT AT THE FRONT OF THE REAR FLIP UP SIGHT. REMOVE THE SPRING BY SLIDING IT FORWARD AND LIFTING IT OUT. SLIDE THE FLANGE NUT INTO THE UNDERCUT AT THE REAR OF THE SIGHT WHERE THE SPRING WAS. PLACE THE MOUNT OVER THE FLANGE NUT WITH THE (2) 4-40 TAPPED HOLES TOWARD THE BARRELL END. LINE THE 4-40 HOLES IN THE MOUNT UP WITH THE HOLES IN THE SIDE OF THE RECEIVER AND PUT IN THE (2) 4-40 SOCKET HEAD SCREWS. DO NOT TIGHTEN!!!
PLACE A PIN, DRILL, ETC. THROUGH THE COUNTERSUNK HOLE IN THE TOP OF THE MOUNT AND INTO THE HOLE IN THE SPECIAL NUT. MOVE THE NUT AROUND WITH THE PIN UNTIL THE ROUND PART OF THE NUT SLIPS INTO THE COUNTERBORE IN THE BOTTOM OF THE MOUNT. PUT THE 10-32 X 5/8 FLAT HEAD SCREW THROUGH THE MOUNT AND INTO THE NUT. TIGHTEN THIS SCREW AND THE (2) 4-40 SCREWS. PUT THE 10 – 32 x ½ SET SCREW DOWN THROUGH THE FRONT TAPPED HOLE IN THE TOP OF THE MOUNT AND TIGHTEN AGAISNT THE RECEIVER. PUT THE 10-32 x 5/16 SET SCREW INTO THE REAR TAPPED HOLE & TIGHTEN. THIS SCREW CAN BE USED FOR SOME VERTICAL ADJUSTMENT. IF YOU FIND YOUR GUN IS SHOOTING LOW, LOOSEN THE 10-32 FLATHEAD, TIGHTEN THE 10-32 x 5/16 SET SCREW AND RE-TIGHTEN THE 10-32 FLATHEAD. FOR EVERY ¼ TURN OF THE FLATHEAD SCREW YOU WILL MOVE APPROXIMATELY 8” AT 100 YARDS.
CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/
