0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Mauser
  5. Scope Mounts
  6. S&K Russian M91, Finish M91, Dragoon, P Series, M24, M27, M28-1 Scout Mount (Weaver Style)-Accepts Weaver Rings- Rings NOT Included
S&K Russian M91, Finish M91, Dragoon, P Series, M24, M27, M28-1 Scout Mount (Weaver Style)-Accepts Weaver Rings- Rings NOT Included
S&K Russian M91, Finish M91, Dragoon, P Series, M24, M27, M28-1 Scout Mount (Weaver Style)-Accepts Weaver Rings- Rings NOT Included

S&K Russian M91, Finish M91, Dragoon, P Series, M24, M27, M28-1 Scout Mount (Weaver Style)-Accepts Weaver Rings- Rings NOT Included

Write a Review
Price: $80.00
This scout mount fits Russian M91, Finish M91, Dragoon, P Series, M24, M27, M28. Made In The USA and accepts Weaver Rings.
Part Number: 9190
Availability:

Fits Russian M91, Finnish M91, Dragoon, P Series, M24, M27, M28

Scout mount attaches to rear sight

Weaver Base

Accepts Weaver Rings-Not Included

Scope and Rings Not Included

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Russian M91, Finnish M91, Dragoon, P Series, M24, M27, or M28 without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.


For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required

 

S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA


#9190 Instruction sheet for Finish M91, Russian M91, Dragoon, P Series, M24, M27 & M28


To install this mount it is necessary to remove the rear sight from your rifle. To remove the rear sight push out the pivot pin, remove the ladder sight & the spring.

After removal of the rear sight place the S&K Mount between the (2) ears sticking up where the ladder sight pivot pin was. Keep the lettering (1891) on the underside of the mount toward the front of the rifle. Line the 4-40 tapped holes in the side of the mount up with the pivot pin holes & insert the (2) 4-40 x 3/8 socket head cap screws. The holes in the rifle sight must line up with the threads in the mount or you can cross-thread the tapped holes in the S&K Mount. Tighten the screws until you feel a slight resistance. They do not need to be very tight. Insert the 10-32 x ½ brass socket set screw into the front top tapped hole of the S&K Mount & tighten this screw. Tightening this screw will put down pressure on the rear of the mount causing the 4-40 screws to become tight. DO NOT try to tighten or loosen the 4-40 screws with the front brass screw tight. Insert the 10-32 x ¼ pointed socket set screw into the top rear threaded hole of the S&K Mount. This screw needs to be tightened only enough to keep the rear of the mount from shifting sideways. Over tightening this screw will lift the rear of the S&K Mount off the pad it rests on & throw elevation off.


CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/


Recently Viewed Items