S&K Schmidt Rubin 1911 Carbine Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

Write a Review

Price: $91.00

This Schmidt Rubin scout mount will mount a long eye relief scope to the rear sight of your old military rifle. Made with pride in the USA.

Part Number: 9665

Availability:

Quantity

Description

Scout Mount

Replaces Rear Sight

Includes S&K Style 1 Inch Rings

Scope Not Included

No alteration needed

Made In The USA!!!

Didn’t think it was possible to easily put a scope and mount on your old Schmidt Rubin 1911 Carbine without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.

For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required

S&K INSTA MOUNT BASES

The BEST WAY to mount a scope on your ex-military rifle. WHY?

-No major alteration to your valuable firearm

-No drilling or tapping of the ultra-hard receiver

-Handsome ruggedness

-Guaranteed to hold zero

-Low cost for a quality product made in the USA!

-Unmatched versatility

-Can be removed and/or reinstalled easily

-Fast service

-Made In The USA

ADVANTAGES OF S&K MOUNTING SYSTEM

-Front and rear rings are interchangeable

-Ring studs mate to matching receptacles in bases

-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)

-Trim in appearance, light in weight

-Precision bored – scope will not slip

-No knobs, bolts or other obtrusions to break or bend

-Fit any 1 inch scope tube

All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8" diameter stud that locks into a 3/8" hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1" diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.

#9665 Instruction sheet for the Swiss Rubin 1911

Push the pin out at the front of the rear sight. Remove the spring by lifting up at the rear and sliding it reward. Slide the flange nut into the undercut at the front of the sight where the spring was. Place the mount over the flange nut with the (2) 4-40 tapped holes toward the barrel end. Line the 4-40 tapped holes in the mount with the holes in the side of the receiver. It is very important that these holes line up to keep from damaging the threads when the screws are installed. Put in the (2) 4-40 socket head screws. DO NOT TIGHTEN!! Place a pin drill etc. through the countersunk hole in the top of the mount and into the hole in the special nut. Move the nut around with the pin until the round part of the nut slips into the counter bore in the bottom of the mount. Put the 10 – 32 x ¾ flat head screw through the mount and into the nut. Tighten this screw and the (2) 4-40 screws. You don’t need to get the (2) 4-40 screws very tight! Put the 10-32 x ½ set screws down through the tapped hole in the top of the mount and tighten against receiver.

CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

S&K 1898 30-40 KRAG & NORW. Scope Mount- w/S&K 1 Inch High Rings

$120.00

Add To Cart

EGW Mauser 98 Large Ring Picatinny Rail Scope Mount 0 MOA (Commercial)

$39.00

Add To Cart

EGW Mauser 98 LR (3-Hole) Picatinny Rail Scope Mount 0 MOA Undrilled (Military)

$39.00

Add To Cart

EGW Mauser 98 LR (3-Hole) Picatinny Rail Scope Mount 20 MOA (Military)

$39.00

Add To Cart

EGW HD Springfield M1903 Picatinny Scope Mount 0 MOA Undrilled

$69.00

Add To Cart

S&K Carcano 91 Carbine w/ 600 - 1500 Sight and Carcano 91 T.S. Troupe Special w/ 600 – 1500 sight (Weaver Style) Scout Mount ) -Accepts Weaver Rings- Rings NOT Included

$94.00

Add To Cart

S&K Schmidt Rubin 1911 Carbine Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

Related Items

Browse Similar Items

Recently Viewed Items