0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Old Military Rifle Scope Mounts
  5. S&K Turkish Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
S&K Turkish Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings
S&K Turkish Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

S&K Turkish Mauser Scout Mount (S&K Style) w/S&K Style 1 Inch Rings

1 Review(s) Write a Review
Price: $84.00
This Turkish Mauser scout mount will allow you to mount a long eye relief scope to the rear sight of your old military rifle. Made with pride in the USA.
Part Number: TK65
Availability:

Includes S&K Style 1 Inch Rings

Scout mount attaches to rear sight

For use with long eye relief scope

No alteration needed

Made In The USA!!!


Didn’t think it was possible to easily put a scope and mount on your old Turkish Mauser without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!

Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.


# TK65 INSTRUCTION SHEET FOR TURKISH MAUSER
Push the pin out at the front of the rear flip up sight.  Remove the flip up sight by pushing down on the sight directly over where the pin was removed & pulling on the flip up sight toward the rear of the gun. There is a sleeve on each side of the flip up sight that has to be pushed down far enough to clear a pocket it fits into. With the sight tipped down at the rear, insert the protruding part of the mount into the undercut at the rear of the gun. You should now be able to push down on the front of the sight until the screw holes are lined up with the pin hole. It is very important that these holes line up to keep from damaging the threads when the screws are installed. Put the two 6-32 x 5/16th button head screws through the holes in the side of the gun and into the mount. Tighten these two screws. You don’t need to get the (2) 6-32 screws very tight! Thread the two 10–32 x ½ set screws into the two top holes & tighten. Make sure they are both tight.

Related Items

S&K 1903 Springfield Scout Mount (Weaver Style)
S&K 1903 Springfield Scout Mount (Weaver Style)
$74.00
Add To Cart
S&K #1 Mark III Scout Mount Weaver Style (No Rings Included)
S&K #1 Mark III Scout Mount Weaver Style (No Rings Included)
$74.00
Add To Cart
S&K 1949 FN Scope Mount w/S&K Style 1 Inch Rings
S&K 1949 FN Scope Mount w/S&K Style 1 Inch Rings
$160.00
Add To Cart
S&K Mosin Nagant 91/30 & 91/59 Scout Mount -Accepts Weaver Rings- Rings NOT Included
S&K Mosin Nagant 91/30 & 91/59 Scout Mount -Accepts Weaver Rings- Rings NOT Included
$74.00
Add To Cart
S&K Schmidt Rubin K-31 Scout Mount -Accepts Weaver Rings- Rings NOT Included
S&K Schmidt Rubin K-31 Scout Mount -Accepts Weaver Rings- Rings NOT Included
$74.00
Add To Cart
UTG Mosin Nagant Tactical Tri Rial Mount
UTG Mosin Nagant Tactical Tri Rial Mount
$33.00
Add To Cart

Browse Similar Items

Recently Viewed Items