0 Items
  1. Home
  2. Shop By Firearm
  3. Shop By Rifle
  4. Winchester
  5. Scope Mounts
  6. S&K Winchester SKulptured Scope Mount Bases With 1 Inch Smooth Kontoured Scope Rings
 S&K Winchester SKulptured Scope Mount Bases With 1 Inch Smooth Kontoured Scope Rings
S&K Winchester SKulptured Scope Mount Bases With 1 Inch Smooth Kontoured Scope Rings

S&K Winchester SKulptured Scope Mount Bases With 1 Inch Smooth Kontoured Scope Rings

Write a Review
Price: $120.00
SKulptured scope bases fit each gun with the contour of the action and fits the radius and height of the barrel. Bases are model specific with rings to match your scope. Made In The USA!
Part Number: Various
Availability:

Choose Options

*
Rifle Scope Bases And 1" Rings - Matte

SKulptured scope bases fit each gun with the contour of the action and fits the radius and height of the barrel. Bases are model specific with rings to match your scope. Made In The USA!

The vertical rings work great:
S&K lock up is non-directional, and applies no torque to the scope tube. S&K has a V-groove that runs completely around the stud. The S&K ring stud fits into a slot that permits no forward movement of the ring stud, but moves left and right okay. In other words, the contact in this are on the S&K mount does not force the cone screws to absorb the recoil.

Bases & Rings Available For:
-Winchester Model 70 Standard and Short Action, & Super Shadow
-Winchester Model 70 (Above 66350)
-Winchester Model 70 Magnum New Extension Mount
-Winchester Model 70 Magnum New Short Action
-Winchester Model 70 Magnum Old Pre 64
-Winchester Model 70 Very Early Model USE HIGH RINGS ONLY May Have To grind Bolt Handle
-Winchester Model 70 Classic Super Short
-Winchester Pre War 70 (High Rings Only Due To Bolt Handle)
-Winchester 52, 52D, 52B
-Winchester 88
-Winchester Low Wall
-Winchester High Wall
-Winchester 52C
-Winchester 54
-Winchester Super Short Mag

Additional scope ring height specs are located in the pictures.

S&K is very proud of this scope mount as it represents the improvements of over 32 years of scope mount manufacture by their company. S&K guarantees this mount for your lifetime. If it fails for any reason other than deliberate destruction, S&K will replace it at no charge! It is handmade in their plant in the Pennsylvania hills by local craftsman who are proud of their work! 

There is no other all steel mount stronger or lighter! Average weight of complete all steel mount – 2 bases and 2 rings – is 3 oz! Windage is provided in both front and rear base and their patented Smooth Kontour rings are the easiest of all rings to install. Good looking? You bet! Cheap? No – they don’t make them of castings or powdered metal, but laboriously machine them from Virgin Bar stock. But the crisp, clean lines complement the finest rifles in the world. Yes, when you choose the S & K Skulptured mount with Smooth Kontour rings, you will know you have the finest available.

S&K offers these options for your mountings in matte.

S&K’S LOWEST 1" SCOPE RINGS are approximately .125 high and place the bottom of the scope approximately .385 above the highest point of your rifle’s receiver when mounted in our lowest height Skulptured bases.

S&K'S MEDIUM 1" SCOPE RINGS will raise the scope an additional .075 above S&K's lowest scope rings (Extra cost)

S&K’S HIGHEST 1" SCOPE RINGS will raise the scope an additional .150 above S&K's lowest scope rings permitting scopes with up to 2-1/16 or 50 mm (Extra cost).

Made In The USA!

CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/

Recently Viewed Items