Fits HAKIM and Egyptian Rashid
Weaver Base
Accepts Weaver Rings (Not Included)
Rings And Scope Not Included
Made In The USA!!!
Didn’t think it was possible to easily put a scope and mount on your old HAKIM or Egyptian Rashid without drilling and tapping? It is now with high quality, made in the USA scope mounts from S&K. These mounts are made with high quality materials and backed by S&K Scope Mounts. Outfit your old military rifle with a scope mount and long eye relief scope for better accuracy, longer ranges, more confidence, and more fun hunting or on the range!
Check out S&K’s line of scout mounts available for ex-military guns! These mounts do not require any alterations to the rifle, just removal of the iron sights. A long eye relief scope (Not Included) is required for a scout mount. A nifty way to scope your treasured gun without drilling or tapping. S&K Scope Mounts LLC supports American made. S&K manufactures all of their scope mounts here in PA with the best USA materials available.
For Instant Scope Mounting of Ex-Military Firearms. No Drilling or Tapping Required
S&K INSTA MOUNT BASES
The BEST WAY to mount a scope on your ex-military rifle. WHY?
-No major alteration to your valuable firearm
-No drilling or tapping of the ultra-hard receiver
-Handsome ruggedness
-Guaranteed to hold zero
-Low cost for a quality product made in the USA!
-Unmatched versatility
-Can be removed and/or reinstalled easily
-Fast service
-Made In The USA
ADVANTAGES OF S&K MOUNTING SYSTEM
-Front and rear rings are interchangeable
-Ring studs mate to matching receptacles in bases
-BOTH rings bear against front of their respective receptacles (both absorb recoil shock)
-Trim in appearance, light in weight
-Precision bored – scope will not slip
-No knobs, bolts or other obtrusions to break or bend
-Fits any 1 inch scope tube
All S&K rings are fully machined out of solid steel bar stock, tumble finished to remove all burrs, and have a 3/8" diameter stud that locks into a 3/8" hole or slot in the base which provides windage adjustment. The rings are locked into position by tightening cooperative cone pointed set screws. The rings are precision bored to 1" diameter and, being machined rather than extruded or stamped, form a precision fit that will not slip under recoil. They are nicely contoured and trim in appearance. S&K rings are tumble finished and blued to achieve a military-type dull or nonglare black finish that matches the black anodized Insta Mount bases.
#HKM70 INSTRUCTION SHEET FOR THE HAKIM
Push the pin out at the front of the rear flip sight. Remove the spring by sliding it forward and lifting it out. Slide the flange nut into the undercut at the rear of the sight where the spring was. It is possible you may need to file the corner edges of the flange nut where it slides into the spring slot. It won’t take much filing if this needs done. Place the mount over the flange nut with the (2) 4-40 tapped holes toward the barrel end. Line the 4-40 holes in the mount up with the holes in the side of the receiver. It is very important that these holes line up to keep from damaging the threads when the screws are installed. Make sure the hole in the receiver hasn’t been damaged. The 4-40 screws should fit into the holes without any interference. Put in the (2) 4-40 socket head screws. Do not tighten!!!
Place a pin, drill, etc. through the countersunk hole in the top of the mount and into the hole in the special nut. Move the nut around with the pin until the round part of the nut slips into the counter-bore in the bottom of the mount. Put the 10-32 x 5/8 flat head screw through the mount and into the nut. Tighten this screw and the (2) 4-40 socket head screws. The 4-40 socket head screws don’t need to be real tight. Put the 10-32 x ½ set screw down through the tapped hole in the top of the mount and tighten against the receiver. The purpose of this setscrew is to keep pressure on the 4-40 button head screws.
If you are willing to remove some wood from the upper handguard you should be able to service the gas tube without removing the scope. At the area where the side 4-40 screws are, cut downward 3/32 to 1/8 & taper that down to nothing at the end of the wood in the rear. Do this on both sides.
CALIFORNIA RESIDENTS ONLY – WARNING: Some products may contain a chemical known to the State of California to cause cancer, or birth defects, or other reproductive harm. For more info, visit https://www.p65warnings.ca.gov/